A stainless-steel enclosure arrives at the sample bench with a few welds marked on its drawing. Before anyone starts welding, someone has to decide whether the opening needs trimming and whether the metal around the joint needs cleaning. After welding, the enclosure goes upright again so the team can check the visible face, the fit of the door and the area around the bead. In a shop that runs small batches, the time spent moving the part, changing tools and resetting a fixture can matter as much as the time spent making the weld.
NICYLAZER designed the NICE-WSX series for shops that regularly move between these jobs. The water-cooled handheld laser welder combines welding, cutting, surface cleaning and weld seam cleaning. It comes with an ergonomically shaped WSX handheld torch and a cabinet on directional casters. A shop welding pre-cut cabinets might use only welding and seam cleaning. A team prototyping a new enclosure might also test local trimming and surface preparation.

Where the water-cooled cabinet fits on the shop floor
The first photograph shows the blue-and-white cabinet, its top-mounted display and controls, and the torch holder on the side. Ask for the configuration sheet for the model being quoted. It should show which accessories come with the machine and which are needed for the modes your shop plans to use.
Water cooling manages heat in the machine. When assessing a model, start with your production schedule. How long are your typical continuous runs? Do operators pause to load another part or keep processing? Is there room around the cabinet for routine maintenance? Check the electrical and environmental requirements against the actual workstation.
Directional casters make the cabinet easier to move across a level floor. That can be useful when a large part is already in a suitable fixture at the next station. Walk the route with the workshop layout in mind. Check whether the cabinet doors can open at the new position, whether cables cross an aisle and whether incoming material has room to pass. Follow the equipment manual for securing the cabinet and checking the lines after moving it.
A shop that prototypes during the day and runs short batches later may benefit from having two established parking positions. One can be near the sample bench and measuring tools. The other can leave room for the loading route. A clearly defined place for the cabinet, the torch and the accessories also makes shift handovers easier.
Try the WSX torch on a real part
The close-up shows the metal torch body and the shaped grip. A torch that feels comfortable over flat sheet on a bench can feel different at the inner corner of a cabinet. Visibility, wrist position and cable pull all change with the orientation of the part.
Bring a flat test coupon, a folded enclosure and one component with a difficult joint. With the machine inactive, have the regular operator check whether the head reaches the joint, whether the fixture obstructs movement and whether there is space to reposition their wrist. Repeat the check with the appropriate accessories for the modes under consideration.
Try taking the torch from its holder and putting it back with the actual workbench layout in place. Look at where the cable falls and whether it can catch on a fixture or drag across a sharp edge. These are small details that a sales photograph cannot show but the operator will deal with on every shift.

Welding starts with the joints you already make
For panel work, enclosures, frames and brackets, bring two or three joints that represent normal orders. Match the material grade, thickness, folded condition and fit-up as closely as possible. A straight bead on flat sheet gives you a first look. The joint most likely to distort, the one that is hard to clamp or the one you can barely see often tells you more about production suitability.
Consider a frame that must accept a cabinet door after welding. Measure the critical points before processing and again afterward. Check whether diagonals and hole positions remain within drawing tolerances. Where appearance matters, compare the bead and adjoining surfaces under the same lighting, and record the fixture and the position of the joint so another operator can reproduce the trial.
Load-bearing, sealed or pressure-retaining parts have their own acceptance requirements. Record appearance alongside the results of the relevant joint inspections. When asking about maximum weld thickness, give the supplier the material, joint type and acceptance criteria. That is a better basis for a configuration and trial than an isolated thickness figure.
Cutting is worth testing on the local trimming jobs
Picture a panel already cut on the main production line. The trial assembly shows that one edge still needs adjustment. Try the cutting function on an offcut from the same batch, then examine whether the edge will meet the next operation’s requirements. Look at fit after assembly and allow for any additional edge finishing.
Test a straight, accessible edge and a more difficult area near a bend or an existing opening. Compare dimensions, edge condition and the total time required. For occasional adjustments, one acceptable part may be enough to demonstrate feasibility. For a repeat order, check whether the fixture is easy to reset and whether inspection can keep pace. This helps decide which work belongs at a handheld station and which stays on the existing production line.
Surface cleaning before joining or finishing
Sheets that look similar at first glance can have different delivery or storage conditions. One might come straight from its packaging while the other shows oxidation or local rust. Start with the part of the surface that actually needs treatment and identify what happens next. Preparation for welding, coating preparation and treatment of an exposed face have different acceptance criteria.
Choose two comparable areas on material from the same batch and keep one as a reference. After the trial, look for residual deposits and changes in the base surface. If the shop regularly receives parts in several different conditions, prepare samples of each. An unusually clean demonstration piece will tell you little about how your normal rework jobs behave.
Find out what coatings or deposits are present before testing. Laser processing can generate fumes and particles, so extraction and waste handling need to suit the workpiece and the material being removed. Include those costs when comparing cleaning methods.
Weld seam cleaning is a separate inspection
Weld seam cleaning deals with the area around the bead after the joint is complete. A customer looking at a metal enclosure sees the whole panel, so review the treated area and the surrounding finish together. A process that looks acceptable close up may stand out under the lighting used for final inspection.
Keep an uncleaned welded sample as a reference and compare it with a treated piece from the same batch under similar lighting. For brushed surfaces and visible panels, pay particular attention to consistency at the boundary of the treated area. If the part will be coated or bonded, include that later operation in the sample assessment. Check joint strength and sealing separately according to the component’s requirements.
Record pre-weld surface cleaning and post-weld seam cleaning as separate steps. If a batch is later rejected, these records help the shop identify where to start looking for the cause.
Put one enclosure through the full sequence
A demonstration of all four modes can show what the machine does. To see whether the NICE-WSX fits the shop, take a familiar part through the whole sequence. On a thin-sheet enclosure, check the opening and bends against the drawing. Decide whether to trim an edge and whether to clean the joint area. After welding, check dimensions and assembly fit before assessing the finish around the visible seam.
Record preparation, processing, accessory changes, resetting the fixture, inspection and rework separately. If the part can stay in its fixture, any time saved may come mainly from avoiding transport and repositioning. If a change of mode still requires the part to move or wait for inspection, count that too. Compare with the existing process using the same part and the same acceptance criteria.
For a second trial, take a similar enclosure with an opening closer to a fold or an inner joint partly obscured by a fixture. This reveals how far the first trial’s documentation can be carried over. Bring production and quality staff into the review before moving the process to a wider range of parts.
Choose a trial around the work you do most
A custom fabrication shop might run a small batch of housings followed by a batch of frames or brackets. Identify the step that most commonly holds up delivery. If post-weld finishing is the bottleneck, compare welding and seam cleaning first. If prototypes repeatedly require changes to an opening, spend the demonstration on how trimming affects the next assembly step.
Repair and modification teams can bring components they have already encountered. Alongside the processing results, check whether the part can be brought into a controlled work area, and whether there is room for both the machine and the necessary fixture. When changing locations, reassess the surroundings, potential reflections and exposure to people nearby.
For prototype work, keep photos and inspection notes for each material and joint. Those records make it easier for production and quality staff to determine which steps can carry over and which need fresh trials at batch scale.
What to provide when requesting a quote
Bring photographs and drawings with the material, thickness, joint location, visible faces and critical dimensions marked. State the one task you most want to improve. That might be reducing the finishing needed around a seam, or handling occasional trimming at the same station as welding. Describe the expected batch size and how the part will be accepted.
Compare quotations against the delivery list for the cabinet, torch, mode-specific accessories, consumables, training and service. Ask how cooling maintenance fits into the shop’s planned downtime. If the NICE-WSX will replace existing equipment, share previous production records and the defects that usually trigger rework. Any performance figures used to compare configurations should identify the model and test conditions.
Make the records useful for the next shift
Assign each trial piece a number. Take one photo showing the complete part and its orientation and another showing the area processed. Record the material batch, accessories, fixture and inspections. Keep unsuccessful samples when they show a meaningful fault, such as a door gap outside the drawing tolerance after an otherwise clean-looking weld.
Industrial laser work requires trained operators and a controlled work area. Follow the equipment manual and site assessment for direct and reflected radiation, wavelength-appropriate protection, extraction, fire hazards and nearby personnel. Reassess the arrangement if the cabinet moves, the material changes or a new mode is introduced. Shift records should make clear who checks the machine, who handles deviations and who accepts each sample.
Start with two components
Bring one component your shop makes every day and one that has always been difficult. The first helps establish a realistic cycle time. The second reveals where access, handling or inspection limits the process. Together they give the shop a better basis for deciding how to use the four modes of the NICE-WSX.
Contact NICYLAZER for the NICE-WSX configuration sheet and a sample trial. Include your usual material grades, thickness range, joint photos and the operation you want to improve.